Irrigation Pump and Well Systems in Nashville and Middle Tennessee
Sprinkler Installation

Irrigation Pump and Well Systems

Booster pumps, well pumps and pump controls matched to your irrigation needs, for properties with low pressure, wells, ponds or large acreage.

Not every property has strong city water. Some have low pressure, a private well, a pond or creek, or a lot of acreage that a standard connection cannot serve. Without enough pressure and flow, heads misfire, zones run weakly and lawn coverage suffers no matter how well the system was laid out. A properly sized pump fixes the supply side and lets the design work as intended.

We start by measuring what you have: pressure, flow, the source and the demand of the zones you want to run. Then we recommend the right pump for the job, whether that is a booster on a city line, a pump for an irrigation well or a pump for pond water. We install the pump with the right pipe, a pressure tank or controller where needed, filtration for pond and well water and the electrical protection and controls to keep it safe and quiet. We explain maintenance and winter care.

Measure before sizing

Pump size depends on pressure, flow and the zones you want to run, so we test before we recommend.

Matched to the source

City boosters, wells and ponds each need different pumps, filters and controls.

Protected and quiet

Proper controls, filtration and mounting protect the pump and keep noise down.

Winter ready

We explain how to drain and protect the pump and show you the steps for your setup.

What is included

  • Pressure and flow testing
  • Source review and pump selection
  • Pump, tank or controller installation
  • Filtration and electrical protection
  • System balancing and testing
  • Care and winter instructions
Before and after

See the transformation.

Drag the handle to compare.

After: a sloped yard with thick green grass and a rotor that waters slowlyBefore: a sloped yard with bare clay streaks and runoff washing downhillBeforeAfter
Eroded slope turned green. From bare clay streaks and runoff washing downhill to thick green grass and a rotor that waters slowly.
Why it works

What you get with Pumps and Wells

Right-sized pump

Based on real numbers.

Pressure fixed

Heads run properly.

Wells and ponds

Alternative sources.

Protected equipment

Controls and filters.

Safe electrical

Done properly.

Winter plan

Explained clearly.

Try it now

Sprinkler Zone Planner: How Many Zones Do I Need?

Enter your lawn and bed areas, head type and water flow to see how many heads and zones a sprinkler system may need.

How it works

Our process, start to finish.

  1. 01

    Call and schedule

    You tell us about your yard and what you want, a new system, a repair or a tune-up, and we set a visit that fits your day.

  2. 02

    Visit and inspect

    We walk the property, find the water source and valves, test pressure and flow, look at every head and zone and take photos of anything of note.

  3. 03

    Design and explain

    We explain your options for zones, heads, drip, controllers and savings, sketch the layout and give you a written scope with clear timing and pricing.

  4. 04

    Prepare the site

    We arrange for underground utilities to be located, protect the lawn, driveways and beds and mark every head, valve and pipe run before we dig.

  5. 05

    Install or repair

    We install or repair pipe, valves, heads and wiring with the right parts for each zone, flush the lines and keep the site tidy as we work.

  6. 06

    Start up and care

    We program the controller, test every zone with you, walk through watering and winterizing in plain steps and set a reminder for your next check.

Questions

Pumps and Wells FAQ

Can I irrigate from a pond or creek?

Often yes, with the right pump and filtration. Water rights and local rules vary, so check them first.

Do I need a pump on city water?

Only if pressure or flow is too low for the zones you want. We test and tell you honestly.

What size pump do I need?

It depends on the flow and pressure needed at the zones. We calculate it from measurements, not guesses.

How do I protect a pump in winter?

Drain it and the connecting lines, and protect it from freezing. We show you the exact steps for your setup.

Is a pump loud?

Properly mounted pumps are quiet enough for most properties. Location and housing make a difference.

Next step

Get your free Pumps and Wells estimate.

Tell us about the project and we will call you back to talk it through.

Or call (615) 357-7797 to talk now.

Tell us about your project

We will call you back to talk it through and set up a visit.

Prefer to talk? Call (615) 357-7797. We never sell your information.

Call NowFree Estimate